2013년 8월 8일 목요일

Cisco 640-875 인증 덤프

ITExamDump는 여러분을 성공으로 가는 길에 도움을 드리는 사이트입니다. ITExamDump에서는 여러분이 안전하게 간단하게Cisco인증640-875시험을 패스할 수 있는 자료들을 제공함으로 빠른 시일 내에 IT관련지식을 터득하고 한번에 시험을 패스하실 수 있습니다.


멋진 IT전문가로 거듭나는 것이 꿈이라구요? 국제적으로 승인받는 IT인증시험에 도전하여 자격증을 취득해보세요. IT전문가로 되는 꿈에 더 가까이 갈수 있습니다. Cisco인증 640-875시험이 어렵다고 알려져있는건 사실입니다. 하지만ITExamDump의Cisco인증 640-875덤프로 시험준비공부를 하시면 어려운 시험도 간단하게 패스할수 있는것도 부정할수 없는 사실입니다. ITExamDump의Cisco인증 640-875덤프는 실제시험문제의 출제방형을 철저하게 연구해낸 말 그대로 시험대비공부자료입니다. 덤프에 있는 내용만 마스터하시면 시험패스는 물론 멋진 IT전문가로 거듭날수 있습니다.


최근 더욱 많은 분들이Cisco인증640-875시험에 도전해보려고 합니다. ITExamDump에서는 여러분들의 시간돠 돈을 절약해드리기 위하여 저렴한 가격에 최고의 품질을 지닌 퍼펙트한Cisco인증640-875시험덤플르 제공해드려 고객님의 시험준비에 편안함을 선물해드립니다. ITExamDump제품을 한번 믿어보세요.


시험 번호/코드: 640-875

시험 이름: Cisco (Building Cisco Service Provider Next-Generation Networks, Part 1)

Cisco 640-875인증시험은 현재IT업계에서 아주 인기 있는 시험입니다.많은 IT인사들이 관연 자격증을 취득하려고 노력하고 있습니다.Cisco 640-875인증시험에 대한 열기는 식지 않습니다.Cisco 640-875자격증은 여러분의 사회생활에 많은 도움이 될 것이며 연봉상승 등 생활보장에 업그레이드 될 것입니다.


ITExamDump에서 제공해드리는 Cisco인증 640-875덤프는 가장 출중한Cisco인증 640-875시험전 공부자료입니다. 덤프품질은 수많은 IT인사들로부터 검증받았습니다. Cisco인증 640-875덤프뿐만아니라 ITExamDump에서는 모든 IT인증시험에 대비한 덤프를 제공해드립니다. IT인증자격증을 취득하려는 분들은ITExamDump에 관심을 가져보세요. 구매의향이 있으시면 할인도 가능합니다. 고득점으로 패스하시면 지인분들께 추천도 해주실거죠?


Cisco인증 640-875시험을 통과하여 자격증을 취득하여 IT 업계에서의 자신의 자리를 지키려면 많은 노력이 필요합니다. 회사일도 바쁜데 시험공부까지 스트레스가 장난아니게 싸이고 몸도 많이 상하겠죠. ITExamDump는 여러분을 위해 최신Cisco인증 640-875시험에 대비한Cisco인증 640-875덤프를 발췌하였습니다. Cisco인증 640-875덤프는Cisco인증 640-875시험의 기출문제와 예상문제가 묶어져 있어 시험적중율이 굉장히 높습니다. 쉽게 시험을 통과하려면ITExamDump의 Cisco인증 640-875덤프를 추천합니다.


640-875 덤프무료샘플다운로드하기: http://www.itexamdump.com/640-875.html


NO.1 Refer to the exhibit.
Company 1 has merged with Company 2. Company 1 is using RIPv2 as its IGP and Company 2 is using
EIGRP as its IGP. EIGRP also is running between R1 and R2 over the WAN link.
Which action must be taken to allow these two configurations?
The Company 1 RIP routes appear as external EIGRP routes within Company 2.
The Company 2 EIGRP routes appear as RIPv2 routes within Company 1.
A. Enable RIPv2 on the R2 router.
B. Enable RIPv2 on the R2 router and on all internal routers of Company 2. Enable EIGRP on all internal
routers of Company 1.
C. Configure mutual route redistribution between RIPv2 and EIGRP on the R1 and R2 routers.
D. Configure mutual route redistribution between RIPv2 and EIGRP on the R1 router.
E. Configure mutual route redistribution between RIPv2 and EIGRP on the R2 router.
Answer: D

Cisco   640-875   640-875 dump

NO.2 Which Cisco IOS CLI command is used to verify the speed and duplex settings on the Fa0/1 port on a
Cisco switch?
A. show ip interfaces fa0/1
B. show interfaces fa0/1
C. show interfaces fa0/1 switchport
D. show ip interfaces brief
E. show interfaces switchport
Answer: B

Cisco   640-875자격증   640-875

NO.3 Which three statements about the ARP function are true? (Choose three.)
A. ARP is used to determine an IP address.
B. An ARP request is broadcast at Layer 3.
C. An ARP response is broadcast at Layer 2.
D. ARP tables are maintained on Layer 3 devices.
E. The destination MAC address of an ARP request is that of the ARP responder.
F. ARP requests are broadcast at Layer 2.
G. ARP resolves MAC addresses to NET addresses.
H. ARP uses 0x0806 as the Type field in an Ethernet frame.
Answer: DFH

Cisco   640-875   640-875   640-875   640-875

NO.4 Given the IP address of 209.168.200.155/27, which two options are the subnet that this IP address
belongs to and the subnet broadcast IP address? (Choose two.)
A. 209.168.200.64 255.255.255.224
B. 209.168.200.96 255.255.255.224
C. 209.168.200.128 255.255.255.224
D. 209.168.200.95
E. 209.168.200.127
F. 209.168.200.159
Answer: CF

Cisco   640-875 pdf   640-875   640-875 pdf

NO.5 Which three physical lines can provide local or remote access to a Cisco router or switch? (Choose
three.)
A. console port
B. modem port
C. virtual terminal lines
D. switch fabric interface
E. aux port
F. managementEthernet0/RSP0/CPU0/0
Answer: AEF

Cisco자격증   640-875 dumps   640-875

NO.6 This show output is from the S7 Cisco Metro Switch and the PE7 Cisco ASR 9000 Series Router. Which
configuration change(s) is/are needed to bring the S7 FastEthernet 0/2 interface into the up/up state?
S7#show cdp neighbors
<OUTPUT OMITTED>
*Mar 20 21:28:02.177: %ETHCNTR-3-HALF_DUX_COLLISION_EXCEED_THRESHOLD:
Collisions at FastEthernet0/2 exceed threshold. Considered as loop-back.
*Mar 20 21:28:02.177: %PM-4-ERR_DISABLE: loopback error detected on Fa0/2, putting Fa0/2 in
err-disable state
*Mar 20 21:28:03.184: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/2, changed
state to down
S7#show interface fa0/2
FastEthernet0/2 is down, line protocol is down (err-disabled)
Hardware is Fast Ethernet, address is e8ba.70b5.6c04 (bia e8ba.70b5.6c04)
MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Half-duplex, 10Mb/s, media type is 10/100BaseTX
input flow-control is off, output flow-control is unsupported
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:00:40, output 00:00:00, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
484423 packets input, 39349929 bytes, 0 no buffer
Received 484423 broadcasts (167203 multicasts)
0 runts, 0 giants, 0 throttles
1 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 watchdog, 167203 multicast, 0 pause input
0 input packets with dribble condition detected
972398 packets output, 128931949 bytes, 0 underruns
0 output errors, 46 collisions, 4 interface resets
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier, 0 PAUSE output
0 output buffer failures, 0 output buffers swapped out
RP/0/RSP0/CPU0:PE7#show interfaces gi0/0/0/0
GigabitEthernet0/0/0/0 is down, line protocol is down
Interface state transitions: 4
Hardware is GigabitEthernet, address is 4055.392f.40a8 (bia 4055.392f.40a8)
Internet address is 192.168.107.70/24
MTU 1514 bytes, BW 100000 Kbit (Max: 100000 Kbit)
reliability 255/255, txload 0/255, rxload 0/255
Encapsulation ARPA,
Full-duplex, 100Mb/s, THD, link type is force-up
output flow control is off, input flow control is off
loopback not set,
ARP type ARPA, ARP timeout 04:00:00
Last input 00:00:00, output 00:00:35
Last clearing of "show interface" counters never
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
972551 packets input, 128953765 bytes, 729 total input drops
172486 drops for unrecognized upper-level protocol
Received 0 broadcast packets, 800781 multicast packets
0 runts, 0 giants, 0 throttles, 0 parity
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
484545 packets output, 39360900 bytes, 0 total output drops
Output 317283 broadcast packets, 167262 multicast packets
0 output errors, 0 underruns, 0 applique, 0 resets
0 output buffer failures, 0 output buffers swapped out
4 carrier transitions
A. Enable loopback line on the S7 Fa0/2 interface then shut and no shut the Fa0/2 interface.
B. Enable duplex half on the PE7 Gi0/0/0/0 interface then shut and no shut the Fa0/2 interface on S7.
C. Change S7 Fa0/2 interface to duplex full and speed 100 then shut and no shut the Fa0/2 interface.
D. Just need to no shut the Fa0/2 interface on S7.
E. Just need to shut and no shut the Fa0/2 interface on S7.
Answer: C

Cisco시험문제   640-875   640-875 dump   640-875

NO.7 Which statement about IPv6 global unicast addresses is true.?
A. The first 3 bits is 001.
B. The first 4 bits is 0011.
C. The first 4 bits is 1111.
D. The first 16 bits is FE80 in hex.
E. The first 16 bits is FF00 in hex.
F. The first 16 bits is 2002 in hex.
G. The first 16 bits is 3FFE in hex.
Answer: A

Cisco   640-875   640-875   640-875

NO.8 If a bridge port is in the non-designated state, which two statements about spanning-tree operations on
this port are true? (Choose two.)
A. This port is in the Forwarding state.
B. This port sends BPDUs on the attached link.
C. This port has the lowest cost to the root bridge.
D. This port is considered the root port.
E. This port receives BPDUs.
F. This port is in the Blocked state.
Answer: EF

Cisco   640-875덤프   640-875

NO.9 With IPv6, for which purpose are router solicitation and router advertisement used?
A. routing protocol updates
B. routing protocol neighbor peerings
C. router and prefix discovery
D. Layer 3 to Layer 2 address resolution (similar to IPv4 ARP)
Answer: C

Cisco자격증   640-875덤프   640-875시험문제   640-875기출문제

NO.10 When EIGRP is enabled on Cisco IOS XR, which EIGRP feature is on by default?
A. no auto-summary
B. stub routing
C. unequal cost paths load-balancing
D. no ip eigrp split-horizon
E. eigrp authentication
Answer: A

Cisco   640-875   640-875   640-875시험문제

NO.11 Which two statements about IPv4 DHCP operations are true? (Choose two.)
A. If the DHCP clients and servers are on the same subnet, DHCP uses UDP broadcasts to communicate
between the clients and servers.
B. The DHCP server that receives a DHCPDISCOVER message may respond with a DHCPOFFER
message on UDP port 67.
C. A client can receive DHCPOFFER from multiple servers and it can accept all the offers by broadcasting
the DHCPREQUEST message to all the servers.
D. A DHCP relay is required if the DHCP clients and the servers are on the same subnet.
E. If the client and server are on different subnets, DHCPDISCOVER and DHCPREQUEST messages
are sent via UDP broadcasts, but DHCPOFFER and DHCPACK messages are unicast.
F. The client broadcasts a DHCPDISCOVER message on UDP port 68 with its own MAC address to
discover available DHCP servers.
Answer: AE

Cisco dump   640-875   640-875

NO.12 Refer to the exhibit.
Given the Class C IP network of 192.168.1.0, using VLSM, which five subnets meet the requirements in
the exhibit? (Choose five.)
A. 192.168.1.0/27
B. 192.168.1.32/27
C. 192.168.1.48/27
D. 192.168.1.48/28
E. 192.168.1.64/28
F. 192.168.1.80/28
G. 192.168.1.80/29
H. 192.168.1.88/30
I. 192.168.1.96/30
Answer: ABEFI

Cisco시험문제   640-875자료   640-875 dumps   640-875최신덤프

NO.13 Which two statements about classful or classless routing protocol operations are true? (Choose two.)
A. Classful routing protocols do not send subnet mask information with their routing updates
B. Variable-length subnet masks are supported when using classful routing protocols.
C. Examples of classless routing protocols include RIPv1, EIGRP, OSPF, and IS-IS.
D. Classful routing protocols do not support discontiguous subnets.
Answer: AD

Cisco기출문제   640-875기출문제   640-875인증   640-875시험문제   640-875   640-875

NO.14 Given the IP address 10.106.170.145 255.248.0.0, which three options are the subnet that this IP
address belongs to, the host IP address range on this subnet, and the subnet broadcast IP
address?(Choose three.)
A. subnet = 10.104.0.0/13
B. subnet = 10.106.0.0/13
C. subnet = 10.112.0.0/13
D. host IP address range = 10.104.0.1 to 10.111.255.254
E. host IP address range = 10.106.0.1 to 10.106.255.254
F. host IP address range = 10.106.0.1 to 10.119.255.254
G. subnet broadcast IP address = 10.106.255.255
H. subnet broadcast IP address = 10.111.255.255
I. subnet broadcast IP address = 10.119.255.255
Answer: ADH

Cisco   640-875 dump   640-875덤프   640-875

NO.15 You are having problems browsing to http://www.cisco.com from your laptop that is running Windows.
Your laptop is connected directly to a default gateway, which is a Cisco ISR G2 router. Which four options
are the basic troubleshooting steps that you should use to troubleshoot this issue? (Choose four.)
A. Issue the ipconfig command from the Windows command line on your laptop to determine your laptop
IP address and the default gateway IP address.
B. Issue the ipconfig /all command from the Windows command line on your laptop to determine the DNS
server IP address.
C. Issue the ping {default gateway IP address} command from the Windows command line on your laptop
to verify connectivity to the default gateway.
D. Issue the ping {DNS server IP address} command from the Windows command line on your laptop to
verify connectivity to the DNS server.
E. Issue the ping tcp www.cisco.com 80 command from the Windows command line on your laptop to
verify TCP port 80 connectivity to the www.cisco.com server.
F. From the ISR G2 CLI, issue the ping tcp www.cisco.com 80 command to verify TCP port 80 connectivity
to the www.cisco.com server.
G. From the ISR G2 CLI, issue the ISR-G2#tracert www.cisco.com command to verify connectivity to the
www.cisco.com server.
H. From the ISR G2 CLI, issue the ISR-G2#nslookup www.cisco.com command to determine the IP
address of the www.cisco.com server.
Answer: ABCD

Cisco   640-875 dump   640-875 pdf   640-875덤프

최근 Cisco인증 640-875시험이 IT업계에서 제일 높은 인지도를 가지고 있습니다.바라만 보지 마시고Cisco인증 640-875시험에 도전해보세요. ITExamDump 의 Cisco인증 640-875덤프로 시험준비공부를 하시면 한방에 시험패스 가능합니다. Cisco인증 640-875덤프로 자격증취득에 가까워지고 나아가서는 IT업계에서 인정을 받는 열쇠를 소유한것과 같다고 할수 있습니다.


댓글 없음:

댓글 쓰기